SKULLCANDY Headphones
Before pairing, please note that most Skullcandy products currently do NOT support aptX-Low Latency codec, hence there will be lip-sync delays when used to watch TV/Video. You may utilize an aptX-LL Bluetooth receiver to eliminate this issue.
Recommended Products: Avantree Clipper Pro, Avantree AS70, Avantree Roxa Plus.
Step 1: Get your Skullcandy Headphone / Speaker into Bluetooth Pairing Mode.
Different products tend to have a different-looking pairing mode... but not to worry, see below for the pairing mode for a list of Skullcandy's most popular products.
- Crusher ANC (EVO): With the headphone turned OFF, Press & Hold the Power button until the LED indicator starts flashing RED & BLUE and you hear a "Pairing" voice prompt.
- Indy ANC (EVO): Put the earbuds on. Press & Hold the Right Earbud's touchpad until you hear a "Pairing" voice prompt.
- Push Ultra: With both earbuds powered off, Press & Hold the buttons on BOTH Earbuds SIMULTANEOUSLY for 6 seconds until the indicators start flashsing RED & BLUE.
- Sesh (EVO): With both earbuds powered off, Press & Hold the buttons on BOTH Earbuds SIMULTANEOUSLY for 6 seconds until the indicators start flashsing RED & BLUE.
Step 2: Put your Avantree Bluetooth transmitter into Pairing Mode as well.
Please refer to its user guide if you're not sure how. With both devices in pairing mode, keep them close to each other and give them a few seconds. Please check their respective LED indicators to make sure that they've connected.
If no luck to get them paired, please Factory Reset/Clear Pairing History of both devices and try again.
Step 1: Factory Reset/Clear Pairing History of your SKULLCANDY Headphones
Crusher ANC (EVO)
1. First, remove your headphones from your device’s Bluetooth paired list. Now, press and hold the top and bottom buttons for 2 seconds.
2. You’ll see the LEDs flash purple first, a voice prompt will say “disconnected” and then the headphone will go into pairing mode, the LEDs will flash blue and red and a voice prompt will say “pairing”.
Indy ANC (EVO):
Once both buds have been powered OFF, reset them: Touch and hold each bud for 10 seconds to completely reset them (this will power cycle them on and off again).
Push Ultra:
1. To ensure ease of re-pairing, please unpair or forget your PUSH™ ULTRA in your paired Bluetooth device list
- Remove the PUSH™ ULTRA from the charging case and Manually Power OFF:
- Touch and hold the Power/MFB button on BOTH buds for 6 seconds
- Once both buds have been powered OFF, reset them: Touch and hold the Power/MFB button on both buds for 10 seconds to completely reset them (this will power cycle them on and off again).
2. Sync the buds together:
- Place the buds back in the case until both LED’s show red, and then pull them back out.
- Both buds will automatically power ON and the LED’s will simultaneously flash BLUE while they sync to each other.
- You will hear a tone to indicate the sync was successful and ONLY the LEFT bud will begin to flash RED/BLUE
Sesh (EVO):
1. To ensure ease of re-pairing, please unpair or forget your SESH® EVO in your paired Bluetooth device list
2. Remove the SESH® EVO from the charging case and Manually Power OFF:
- Touch and hold BOTH buds for 6 seconds
3. Once both buds have been powered OFF:
- Touch and hold each bud for 10 seconds to completely reset them (this will power cycle them on and off again).
4. Once both buds have gone through the power cycle:
- Place the buds back in the case until both LED’s show red, and then pull them back out.
- Both buds will automatically power ON and the LED’s will simultaneously flash BLUE while they sync to each other.
5. Once the buds have synced together:
- You will hear a tone to indicate the sync was successful and ONLY the LEFT bud will begin to flash RED/BLUE.
Step 2: Factory Reset Avantree Bluetooth Transmitter
Please refer to its user guide if you're not sure how.Once this is done, the Oasis Plus will re-enter pairing mode.
Please contact us at support@avantree.com if you have any question.
