PANASONIC Headphones
Before pairing, please note that most Panasonic products currently do NOT support aptX-Low Latency codec, hence there will be lip-sync delays when used to watch TV/Video. You may utilize an aptX-LL Bluetooth receiver to eliminate this issue.
Recommended Products: Avantree Clipper Pro, Avantree AS70, Avantree Roxa Plus.
Step 1: Get your Panasonic Headphone / Speaker into Bluetooth Pairing Mode.
Different products tend to have a different-looking pairing mode... but not to worry, see below for the pairing mode for a list of Panasonic's most popular products.
- RP-HD600N/605N/HD610N/HD805N: With the headphone turned OFF, Press & hold the power button for 5 seconds until the BLUE & RED indicator flashes alternately.
- RZ-S500W: For first-time pairing, the earbuds will enter pairing mode when removed from the case. For pairing with a second (and on) device, remove the earbuds from the case, tap & hold the left or right touch panel for seven seconds until the LEDs will alternate between RED & BLUE.
- RB-M500B: With the headphone turned OFF, Press & hold the power button for 5 seconds until the BLUE & RED indicator flashes alternately.
- WINGS BTS50: With the headphone turned OFF, Press & hold the power button for 5 seconds until the BLUE & RED indicator flashes alternately.
- EAH-F50B/F70N: With the headphone turned OFF, Press & hold the power button for 5 seconds until the BLUE & RED indicator flashes alternately.
- BTG-S10: With the headphone turned ON, Press & hold the Bluetooth button for 2 seconds until the MAGNETA & RED indicator flashes alternately.
Step 2: Put your Avantree Bluetooth transmitter into Pairing Mode as well.
Please refer to its user guide if you're not sure how. With both devices in pairing mode, keep them close to each other and give them a few seconds. Please check their respective LED indicators to make sure that they've connected.
If no luck to get them paired, please Factory Reset/Clear Pairing History of both devices and try again.
Step 1. Factory reset/Clear Pairing History your Panasonic headphones
RP-HD600N/605N/HD610N/HD805N:
1. While the unit is turned off, press and hold 
2. While the power/pairing LED is blinking alternately in blue and red, slide and hold the [Multiple functions button] towards "+" and at the same time press and hold
The default settings will be restored after the power/pairing LED (blue) blinks fast and the unit turns off.
Attention:
When pairing the device again, delete the registering information (Device: HD605N) from the bluetooth device menu, and register this unit with bluetooth device again.
RZ-S500W:
1. Take the R side earphone out of the charging cradle.
2. While the earphone lights (blue), touch and hold the touch sensor (R) for about 7 seconds.The earphone LED will light alternately in blue and red.
3. Touch and hold the touch sensor (R) for about 10 seconds. The earphone LED (blue) blinks rapidly, and when the power turns off, the earphone returns to the factory settings.
4. Do the same steps 1 to 3 above to the L side earphone.
RB-M500B:
1. While the power is turned off, press and hold 
2. While the power/pairing LED is blinking alternately in blue and red, press and hold [+] and [-] at the same time for at least 5 seconds. The default settings will be restored after the power/pairing LED (blue) blinks fast and the unit turns off.
Attention: When pairing the device again, delete the registering information (Device:"RB-M500B" ) from the bluetooth device menu, and register this unit with bluetooth device again.
2. Factory Reset Avantree Bluetooth Transmitter:
Please refer to its user guide if you're not sure how.Once this is done, the Oasis Plus will re-enter pairing mode.
Please contact us at support@avantree.com if you have any question.
