SHIPPING

We have warehouses located in the US, EU, Canada, and Australia; orders placed in other regions will be delivered via international shipping.

RETURNS

Free returns within 60 days of purchase date. Once we receive the item, a refund will be initiated immediately.

WARRANTY

All purchases from Avantree.com automatically comes with a 24-month warranty.

BULK DISCOUNTS

Discount prices will automatically
be reflected in the shopping cart

For same item orders:

• 5-9receive 5%   off order total
• 10-19receive 10% off order total
• 20+receive 15% off order total

JBL Speakers & Headphones

This guide is under the category of General Information

Applies to all of our products.

Click on the product name to view this guide & find more help on the full product support page:

Categories
JBL Speakers & Headphones

This guide applies to all of our products > General Information Go to full support page

Before pairing, please note that JBL products currently do NOT support aptX-Low Latency codec, hence there will be lip-sync delays when used to watch TV/Video. You may utilize an aptX-LL Bluetooth receiver to eliminate this issue.

Recommended Products: Avantree Clipper Pro, Avantree AS70, Avantree Roxa Plus.

Step 1: Get your JBL Headphone / Speaker into Bluetooth Pairing Mode.

Different products tend to have a different-looking pairing mode... but not to worry, see below for the pairing mode for a list of JBL's most popular products.

  • JBL Flip 4: Turn on the Flip by pressing the ON/OFF power button. Then press the Bluetooth button and you will hear an acoustic signal. The pairing mode is activated.
    How to Connect JBL Flip to TV

  • JBL E45BT/E55BT: With the headphone ON, press & hold the Bluetooth button for 5 seconds to put the headphones into pairing mode. You'll hear corresponding sound notification through the headphones.
    How to Connect JBL Headphones to TV
  • JBL Charge: With the speaker turned ON, press the Bluetooth button. The Power button will start flashing BLUE and you will hear an audible noise.

    How to Connect JBL Charge to TV
  • JBL Go (2): With the speaker turned ON, press the Bluetooth button to get JBL Go into Pairing mode.

    How to Connect JBL Go Speaker to TV
  • JBL Live 400BT/500BT/650BTNC: Press the "Bluetooth" button located along the bottom of the right ear cover. The BLUE power light on the back of the right ear cover will start blinking.

    How to Connect JBL live to TV
  • JBL Under Armor Flash:  Begin with the headphones powered off and hold the center button on the RIGHT ear bud for 5 seconds to enter pairing mode. You will hear the Bluetooth pairing audible chime as it searches for a different device.
    How to connect JBL under armor to TV

Step 2: Put your Avantree Bluetooth transmitter into Pairing Mode as well.

Please refer to its user guide if you're not sure how. With both devices in pairing mode, keep them close to each other and give them a few seconds. Please check their respective LED indicators to make sure that they've connected.

If no luck to get them paired, please Factory Reset/Clear Pairing History of both devices and try again.

Step 1: Factory Reset/Clear Pairing History of your JBL Speaker & Headphones.

JBL Flip 4:

Hold both the "Volume Up" and "Play" buttons down until the device turns off by itself. You can tell the device has powered down when the blue backlight behind the Power button is no longer on, and when you hear the standard power down sound

JBL E45BT/E55BT:

With the headphones switched ON, press and hold the Volume + and Volume – buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.

JBL Charge 3:

1. Turn on the speaker.

2. Press the volume up and play pause button at the same time for about 3 seconds. As soons as the speaker powers off, release your hands from the buttons.

3. Power the speaker back on again.  

JBL Charge 4: 

1. Press the power button to turn on the speaker. 

2. Hold on the bluetooth and volume up buttons at the same time about 3 seconds. The LED ring around the power and bluetooth buttons will briefly light up before the JBL Charge 4 powers down. 

3. Press the power button again to turn the speaker back on again. The Charge 4 will instantly turn on in discovery mode, with the bluetooth LED blinking on and off. 

JBL GO 2:

1. Turn on the speaker. Press and hold the Power button until the status lamp on the front top lights up and the guitar strum sound plays.

2. Press the volume up and bluetooth buttons together to continue with JBL GO 2 reset.

3. Within a second or two, the unit powers off after reset finishes.

4. Power on the speaker again. JBL Go 2 comes up in ready-to-pair mode, with the status lamp rapidly flashing blue.

JBL Live 400BT/500BT/650BTNC:

1. Power on the headphones.

2. Hold down the the "Volume Up" and "Volume Down" buttons at the same time for roughly five seconds until you hear the device make sound, indicating it is powering down.

3. Release the volume buttons.The device makes the following powering on sound again which is followed by a pinging sound.

JBL Under Armor Flash:

To reset, press and hold the RIGHT ear bud button for 2 seconds with the earbud in the case. The blue LED will flash once to indicate reset is done.

Step 2: Factory Reset Avantree Bluetooth Transmitter

Please refer to its user guide if you're not sure how.Once this is done, the Oasis Plus will re-enter pairing mode.

Please contact us at support@avantree.com if you have any question.

 

Was this answer helpful?
Views
Facebook Twitter Reddit Tumblr
TOP