SHIPPING

We have warehouses located in the US, EU, Canada, and Australia; orders placed in other regions will be delivered via international shipping.

RETURNS

Free returns within 60 days of purchase date. Once we receive the item, a refund will be initiated immediately.

WARRANTY

All purchases from Avantree.com automatically comes with a 24-month warranty.

BULK DISCOUNTS

Discount prices will automatically
be reflected in the shopping cart

For same item orders:

• 5-9receive 5%   off order total
• 10-19receive 10% off order total
• 20+receive 15% off order total

BEATS Headphones & Speakers

This guide is under the category of General Information

Applies to all of our products.

Click on the product name to view this guide & find more help on the full product support page:

Categories
BEATS Headphones & Speakers

This guide applies to all of our products > General Information Go to full support page

Before pairing, please note that Beats products currently do NOT support aptX-Low Latency codec, hence there will be lip-sync delays when used to watch TV/Video. You may utilize an aptX-LL Bluetooth receiver to eliminate this issue.

Recommended Products: Avantree Clipper Pro, Avantree AS70, Avantree Roxa Plus.


Step 1: Get your Beats Headphone / Speaker into Bluetooth Pairing Mode.

Different products tend to have a different-looking pairing mode... but not to worry, see below for the pairing mode for a list of Beats' most popular products.

  • Beats Studio 3 Wireless: With the headphones turned OFF, press & hold the power button for 5 seconds until the five Fuel Gauge lights start flashing.
  • Beats Solo 3 Wireless: With the headphones turned OFF, press & hold the power button for 5 seconds until the five Fuel Gauge lights start flashing.
  • Powerbeats Wireless: With the earbuds turned OFF, press & hold the power button for 5 seconds until the LED indicator starts flashing.
  • Powerbeats Pro: Place the earbuds inside the case and press & hold the System Button for a few seconds until you see the pairing light flash.
  • Beats Pill+ Speaker: Turn the speaker ON,  press & hold the "b" for 3 seconds until the Bluetooth LED located at the rear of the Pill blinks WHITE.


  • Beats X Wireless: With the earbuds turned OFF, press & hold the power button for 5 seconds until the LED indicator starts flashing.


Step 2: Put your Avantree Bluetooth transmitter into Pairing Mode as well.

Please refer to its user guide if you're not sure how. With both devices in pairing mode, keep them close to each other and give them a few seconds. Please check their respective LED indicators to make sure that they've connected.

In case you prefer Learning through Videos:

 

If no luck to get them paired, please Factory Reset/Clear Pairing History on Both Devices and try again.

Step 1: Factory Reset/Clear Pairing History of your Beats Headphone / Speaker

 Beats Studio 3 Wireless:

1. Hold down the power button and volume down button for 10 seconds.

2. When the Fuel Gauge flashes, release the buttons.

3. Your headphones are now reset and ready to be set up with your devices again.

Beats Solo 3 Wireless:

1. Hold down the volume down button and the power button for 10 seconds.

2. When the Fuel Gauge flashes, release the buttons.

3. Your headphones are now reset and ready to be set up with your devices again.

Powerbeats Wireless:

1. Hold down both the power button and volume down button for 10 seconds.

2. When the LED indicator light flashes, release the buttons. Your earphones are now reset and ready to be set up with your devices again.

  Powerbeats Pro:

1. Put both Powerbeats Pro earphones in the charging case

2. Press the button on the inside of the case until the indicator light flashes red and white, let go

3. The LED should be flashing white, which means they are ready to re-pair with your iPhone or another device

Beats Pill+ Speaker:

1. Use the Lightning-to-USB cable to plug your Beats Pill+ into a power source.

2. Turn the speaker on.

3. Hold down both the "b" button and the power button for six seconds. The Fuel Gauge flashes red six times. Your Beats Pill+ is now restored to the settings it had when you purchased it.

 Beats X Wireless:

1. Hold down both the power button and volume down button for 10 seconds.

2. When the LED indicator light flashes, release the buttons. Your earphones are now reset and ready to be set up with your devices again.

Step 2: Factory Reset/Clear Pairing History of Avantree Bluetooth Transmitter:

Please refer to its user guide if you're not sure how.Once this is done, the Oasis Plus will re-enter pairing mode.

Please contact us at support@avantree.com if you have any question.

Was this answer helpful?
Views
Facebook Twitter Reddit Tumblr
TOP