AVANTREERelay · BTTC-218

INTERACTIVE USER GUIDE

Relay Setup Guide

Four steps. One clear result.

Relay sends 3.5 mm audio to your headphones. Pair them to Relay—not your phone.

Keep both within 3 ft / 1 m while pairing.

1

HEADPHONES

Put your headphones in pairing mode

Turning them on is not enough.
  1. Turn off nearby Bluetooth.
  2. Put your headphones in Bluetooth pairing mode.
  3. Wait for a pairing light or prompt.

DONEYour headphones are searching.

IF NOTOpen the brand help below.

Headphone pairing helpChoose brand
AirPods
  1. AirPods 1-3 and AirPods Pro 1-2: keep them in the case, open the lid, then hold the rear setup button for about 5 seconds.
  2. AirPods 4 and AirPods Pro 3: keep them in the case, open the lid, then double-tap the front of the case.
  3. Ready when the case light flashes white.
AirPods Max
  1. Hold the listening mode button for about 5 seconds.
  2. Ready when the status light flashes white.
Bose
  1. Controls vary by model. Follow the model's Bluetooth pairing steps until the light flashes blue or a voice says it is ready to connect.
Beats
  1. Controls vary by model. Follow the model's Bluetooth pairing steps until its indicator flashes.
Sony
  1. Controls vary by model. Follow the model's Bluetooth pairing steps until the light flashes blue or you hear a pairing prompt.
Samsung
  1. For Galaxy Buds, put both buds in the case, close it for 5-6 seconds, then open it. Follow the model guide if they do not enter pairing mode.
JBL
  1. Controls vary by model. Follow the model's Bluetooth pairing steps until the indicator flashes blue.
Sennheiser
  1. Controls vary by model. Follow the model's official Bluetooth pairing instructions and wait for its pairing indicator or voice prompt.
Other
  1. Check the headphone manual for Bluetooth pairing mode. Do not stop after only turning the headphones on.
2

RELAY

Put Relay in pairing mode

  1. Slide Relay’s power to ON.
Red + blue flashingRelay is searching

DONERelay is searching.

IF NOTOnly blue? Hold MFB until the light flashes red + blue.

Avantree Relay with its large round MFB button
MFB
3

CONNECT

Let them connect

  1. Keep both devices within 3 ft / 1 m.
  2. Wait for the Relay light to change.
Solid blueConnected

DONESolid blue means your headphones are connected.

IF NOTStill red + blue? Repeat Step 1.

4

PLAY

Plug in and play

  1. Plug Relay into a 3.5 mm AUDIO OUT.
  2. Start the audio.
  3. Raise all three volumes slowly.
1SourceAirplane screen→2Relay+ / − buttons→3HeadphonesVolume

Important: Use AUDIO OUT, not AUDIO IN.

DONESolid blue + sound.

QUICK HELP

Fix the four common problems

01
No connectionLight never turns solid blue
  1. Turn off Bluetooth on nearby phones, tablets, and computers.
  2. Put the headphones in pairing mode again.
  3. Hold Relay's MFB until red and blue flash alternately, then keep both devices close.

DONEThe Relay light turns solid blue.

02
Connected but no soundSolid blue, silent headphones
  1. Push the plug fully into a 3.5 mm AUDIO OUT or headphone jack.
  2. Start audio and raise the source or airplane screen volume.
  3. Raise Relay with its + button, then raise the headphone volume.

DONESound plays through the connected headphones.

03
Add second headphonesKeep the first pair connected
  1. Keep the first headphones connected and confirm their Relay indicator is solid blue.
  2. Hold Relay's MFB until the second indicator flashes red and blue.
  3. Put the second headphones in pairing mode and keep them close to Relay.
  4. Wait until both Relay headphone indicators are solid blue.

DONEBoth Relay headphone indicators are solid blue.

For the most stable dual connection, use two over-ear headphones or two identical earbud sets.

04
Clear pairing historyRemove old saved connections
  1. Turn on Relay.
  2. Hold the + and - buttons together for 6 seconds.
  3. Wait for the red and blue lights to stay on together for 3 seconds.
  4. Pair the headphones with Relay again from Step 1.

DONERelay's saved Bluetooth pairing history is cleared and the headphones can be paired again.

Full manual (PDF) ↗Contact support ↗